John Deere 26G 500h oil ยท 500h filters ยท Free for 2 machines
Track this John Deere 26G Free โ€” Auto-Load All Service Intervals

John Deere 26G Maintenance Schedule (500h Chart)

Use this schedule as a field planning aid for the 20 hp Yanmar 3TNV80F diesel. 2.6-ton trailerable excavator: use Deere Plus-50 II oil for 500h intervals or change at 250h with standard oil.

Pre-load this John Deere 26G into your free maintenance log Auto-loads 500h oil & 500h filter alerts, filter part-number vault, and resale binder. Free forever for 2 machines โ€” no credit card required.

John Deere 26G interval summary

Service itemTypical intervalField note
Engine oil500 hoursShorten for dusty, hot, idle-heavy, or severe-duty work.
Hydraulic fluid1000 hoursWatch for contamination, overheating, slow functions, or leaks.
Filters500 hoursIncludes engine oil, fuel, air, hydraulic, or separator filters as equipped.
Grease pointsDaily to 50 hoursDaily bucket, arm, boom, swing post, and blade pivots every 10โ€“50 hours
Tracks / tires / running gearEvery shiftInspect rubber tracks, tension grease valve, idlers, and travel motor oil every 250 hours

Service milestone checklist (50h / 500h / 500h / 1,000h)

DoneHour milestoneWhat to inspect & service
โ˜Daily / Every 10 hoursWalkaround fluid check (engine oil, coolant, hydraulic sight glass), daily bucket, arm, boom, swing post, and blade pivots every 10โ€“50 hours, and inspect rubber tracks, tension grease valve, idlers, and travel motor oil every 250 hours
โ˜First 50 hours (Break-in)Initial break-in engine oil & filter service (and hydraulic charge/return filter where required), re-torque hardware/lugs, check belt & hose clamps.
โ˜Every 500 hoursEngine oil & oil filter change, inspect air cleaner element, drain fuel water separator, inspect battery terminals and cooling core.
โ˜Every 500 hoursPrimary fuel filter(s), engine air filters, hydraulic/hydrostatic filter service, and driveline/final-drive oil level check.
โ˜Every 1000 hoursFull hydraulic fluid service (1000h), suction strainer inspection, coolant flush check, and valve lash inspection.

Always verify capacities, fluids, filters, break-in service, and exact intervals against your operator's manual and warranty requirements.

Track your John Deere 26G intervals automatically in EquipHours

Stop tracking 500-hour oil changes and 500-hour filter services on paper. Load this John Deere 26G schedule into EquipHours for push + email overdue alerts, filter part-number vault, verified resale binder, and printable QR decals.

๐Ÿ”ง Repair shop or equipment dealer? Put your shop on cab stickers & earn recurring commission via Residual Apps โ†’

Mini Excavators maintenance tips

Mini excavators live on pins, bushings, hydraulic oil, and clean undercarriages. The easiest preventive win is daily greasing with the bucket, arm, boom, blade, and swing points visible before the operator starts trenching. Track tension should be checked on level ground and cleaned after muddy work so packed material does not over-tighten the rubber track. Watch for weeping cylinder seals, loose bucket hardware, and damaged coupler locks. If the excavator runs a hammer, auger, or thumb most days, inspect auxiliary lines and fittings more often than the standard schedule suggests.

Frequently asked questions

How often should you change engine oil on a John Deere 26G?

Typical John Deere 26G service calls for changing engine oil every 500 operating hours (after the initial 50-hour break-in service), or sooner in dusty, hot, or heavy-load conditions.

When are filters and fluids due on the John Deere 26G?

Primary filter service is typically scheduled every 500 hours, with hydraulic fluid service around 1000 hours. 2.6-ton trailerable excavator: use Deere Plus-50 II oil for 500h intervals or change at 250h with standard oil.

What is included in the 50-hour break-in service on a John Deere 26G?

At the first 50 hours on a new or rebuilt John Deere 26G, inspect and replace break-in engine oil and filters (Plus hydraulic return/charge filters if specified in the operator's manual), verify wheel lug or track tension torque, check belt tension, and inspect all hoses and fittings for early leaks.

What is on the daily pre-start checklist for the John Deere 26G?

Inspect rubber tracks, tension grease valve, idlers, and travel motor oil every 250 hours. Daily bucket, arm, boom, swing post, and blade pivots every 10โ€“50 hours. Log every hour-meter reading and service task in EquipHours.

How do I track John Deere 26G maintenance hours automatically?

You can load the John Deere 26G (500h oil / 500h filter intervals) directly into EquipHours for free (up to 2 machines free forever, no credit card required) to log engine hours in 10 seconds and get automatic overdue alerts.

Related mini excavators schedules

Track these intervals automatically with EquipHours

Set hour or mile intervals once, let crews log service in the field, and see what is coming due before a missed PM becomes downtime.