Scag Tiger Cat II 100h oil · 100h filters · Free for 2 machines

Scag Tiger Cat II Maintenance Schedule (100h Chart)

Use this schedule as a field planning aid for the Commercial V-Twin gas zero-turn mower. Change hydraulic oil and filter after the first 75–100 break-in hours, then every 400–500 hours.

Pre-load this Scag Tiger Cat II into your free maintenance log Auto-loads 100h oil & 100h filter alerts, filter part-number vault, and resale binder. Free forever for 2 machines — no credit card required.

Scag Tiger Cat II interval summary

Service itemTypical intervalField note
Engine oil100 hoursShorten for dusty, hot, idle-heavy, or severe-duty work.
Hydraulic fluid400 hoursWatch for contamination, overheating, slow functions, or leaks.
Filters100 hoursIncludes engine oil, fuel, air, hydraulic, or separator filters as equipped.
Grease pointsDaily to 50 hoursGrease cast-iron deck spindles, caster pivots, and pump belt idler arms every 40 hours
Tracks / tires / running gearEvery shiftInspect drive tires, caster bearings, deck belt tension, and blade sharpness every 8 hours

Service milestone checklist (50h / 100h / 100h / 1,000h)

DoneHour milestoneWhat to inspect & service
☐Daily / Every 10 hoursWalkaround fluid check (engine oil, coolant, hydraulic sight glass), grease cast-iron deck spindles, caster pivots, and pump belt idler arms every 40 hours, and inspect drive tires, caster bearings, deck belt tension, and blade sharpness every 8 hours
☐First 50 hours (Break-in)Initial break-in engine oil & filter service (and hydraulic charge/return filter where required), re-torque hardware/lugs, check belt & hose clamps.
☐Every 100 hoursEngine oil & oil filter change, inspect air cleaner element, drain fuel water separator, inspect battery terminals and cooling core.
☐Every 100 hoursPrimary fuel filter(s), engine air filters, hydraulic/hydrostatic filter service, and driveline/final-drive oil level check.
☐Every 400 hoursFull hydraulic fluid service (400h), suction strainer inspection, coolant flush check, and valve lash inspection.

Always verify capacities, fluids, filters, break-in service, and exact intervals against your operator's manual and warranty requirements.

Track your Scag Tiger Cat II intervals automatically in EquipHours

Stop tracking 100-hour oil changes and 100-hour filter services on paper. Load this Scag Tiger Cat II schedule into EquipHours for push + email overdue alerts, filter part-number vault, verified resale binder, and printable QR decals.

🔧 Repair shop or equipment dealer? Put your shop on cab stickers & earn recurring commission via Residual Apps →

Commercial Mowers maintenance tips

Commercial zero-turn mowers rack up hours quickly and operate in dust, grass clippings, heat, and vibration. Daily blade, belt, tire, and deck checks prevent rough cuts and avoid small issues turning into spindle or hydro drive repairs. Oil and air filters deserve close attention during dry mowing because clogged filters shorten engine life. Keep deck buildup under control, verify blade bolt torque after blade changes, and record hydro service separately from engine oil. Crews should log service when the mower comes off the trailer, not days later when the hour reading has already changed.

Frequently asked questions

How often should you change engine oil on a Scag Tiger Cat II?

Typical Scag Tiger Cat II service calls for changing engine oil every 100 operating hours (after the initial 50-hour break-in service), or sooner in dusty, hot, or heavy-load conditions.

When are filters and fluids due on the Scag Tiger Cat II?

Primary filter service is typically scheduled every 100 hours, with hydraulic fluid service around 400 hours. Change hydraulic oil and filter after the first 75–100 break-in hours, then every 400–500 hours.

What is included in the 50-hour break-in service on a Scag Tiger Cat II?

At the first 50 hours on a new or rebuilt Scag Tiger Cat II, inspect and replace break-in engine oil and filters (Plus hydraulic return/charge filters if specified in the operator's manual), verify wheel lug or track tension torque, check belt tension, and inspect all hoses and fittings for early leaks.

What is on the daily pre-start checklist for the Scag Tiger Cat II?

Inspect drive tires, caster bearings, deck belt tension, and blade sharpness every 8 hours. Grease cast-iron deck spindles, caster pivots, and pump belt idler arms every 40 hours. Log every hour-meter reading and service task in EquipHours.

How do I track Scag Tiger Cat II maintenance hours automatically?

You can load the Scag Tiger Cat II (100h oil / 100h filter intervals) directly into EquipHours for free (up to 2 machines free forever, no credit card required) to log engine hours in 10 seconds and get automatic overdue alerts.

Related commercial mowers schedules

Track these intervals automatically with EquipHours

Set hour or mile intervals once, let crews log service in the field, and see what is coming due before a missed PM becomes downtime.