Scag Cheetah II 100h oil · 100h filters · Free for 2 machines

Scag Cheetah II Maintenance Schedule (100h Chart)

Use this schedule as a field planning aid for the Commercial V-Twin gas engine (Kawasaki FX / Vanguard / Kohler EFI). Break-in engine oil at 8–20 hours and ZT-5400 transaxle oil/filter at 100 hours, then transaxle service every 500 hours.

Pre-load this Scag Cheetah II into your free maintenance log Auto-loads 100h oil & 100h filter alerts, filter part-number vault, and resale binder. Free forever for 2 machines — no credit card required.

Scag Cheetah II interval summary

Service itemTypical intervalField note
Engine oil100 hoursShorten for dusty, hot, idle-heavy, or severe-duty work.
Hydraulic fluid500 hoursWatch for contamination, overheating, slow functions, or leaks.
Filters100 hoursIncludes engine oil, fuel, air, hydraulic, or separator filters as equipped.
Grease pointsDaily to 50 hoursGrease Velocity Plus cutter deck spindles, caster wheel bearings/pivots, and operator suspension platform every 40–100 hours
Tracks / tires / running gearEvery shiftCheck tire pressure (12 psi drive tires), blade bolt torque, deck belts, and grass buildup daily

Service milestone checklist (50h / 100h / 100h / 1,000h)

DoneHour milestoneWhat to inspect & service
☐Daily / Every 10 hoursWalkaround fluid check (engine oil, coolant, hydraulic sight glass), grease velocity plus cutter deck spindles, caster wheel bearings/pivots, and operator suspension platform every 40–100 hours, and check tire pressure (12 psi drive tires), blade bolt torque, deck belts, and grass buildup daily
☐First 50 hours (Break-in)Initial break-in engine oil & filter service (and hydraulic charge/return filter where required), re-torque hardware/lugs, check belt & hose clamps.
☐Every 100 hoursEngine oil & oil filter change, inspect air cleaner element, drain fuel water separator, inspect battery terminals and cooling core.
☐Every 100 hoursPrimary fuel filter(s), engine air filters, hydraulic/hydrostatic filter service, and driveline/final-drive oil level check.
☐Every 500 hoursFull hydraulic fluid service (500h), suction strainer inspection, coolant flush check, and valve lash inspection.

Always verify capacities, fluids, filters, break-in service, and exact intervals against your operator's manual and warranty requirements.

Track your Scag Cheetah II intervals automatically in EquipHours

Stop tracking 100-hour oil changes and 100-hour filter services on paper. Load this Scag Cheetah II schedule into EquipHours for push + email overdue alerts, filter part-number vault, verified resale binder, and printable QR decals.

🔧 Repair shop or equipment dealer? Put your shop on cab stickers & earn recurring commission via Residual Apps →

Commercial Mowers maintenance tips

Commercial zero-turn mowers rack up hours quickly and operate in dust, grass clippings, heat, and vibration. Daily blade, belt, tire, and deck checks prevent rough cuts and avoid small issues turning into spindle or hydro drive repairs. Oil and air filters deserve close attention during dry mowing because clogged filters shorten engine life. Keep deck buildup under control, verify blade bolt torque after blade changes, and record hydro service separately from engine oil. Crews should log service when the mower comes off the trailer, not days later when the hour reading has already changed.

Frequently asked questions

How often should you change engine oil on a Scag Cheetah II?

Typical Scag Cheetah II service calls for changing engine oil every 100 operating hours (after the initial 50-hour break-in service), or sooner in dusty, hot, or heavy-load conditions.

When are filters and fluids due on the Scag Cheetah II?

Primary filter service is typically scheduled every 100 hours, with hydraulic fluid service around 500 hours. Break-in engine oil at 8–20 hours and ZT-5400 transaxle oil/filter at 100 hours, then transaxle service every 500 hours.

What is included in the 50-hour break-in service on a Scag Cheetah II?

At the first 50 hours on a new or rebuilt Scag Cheetah II, inspect and replace break-in engine oil and filters (Plus hydraulic return/charge filters if specified in the operator's manual), verify wheel lug or track tension torque, check belt tension, and inspect all hoses and fittings for early leaks.

What is on the daily pre-start checklist for the Scag Cheetah II?

Check tire pressure (12 psi drive tires), blade bolt torque, deck belts, and grass buildup daily. Grease Velocity Plus cutter deck spindles, caster wheel bearings/pivots, and operator suspension platform every 40–100 hours. Log every hour-meter reading and service task in EquipHours.

How do I track Scag Cheetah II maintenance hours automatically?

You can load the Scag Cheetah II (100h oil / 100h filter intervals) directly into EquipHours for free (up to 2 machines free forever, no credit card required) to log engine hours in 10 seconds and get automatic overdue alerts.

Related commercial mowers schedules

Track these intervals automatically with EquipHours

Set hour or mile intervals once, let crews log service in the field, and see what is coming due before a missed PM becomes downtime.